Skip to main content

Preliminary Research and Documentation

YxJNyfFQ.jpeg

 

 

image-1617549379283.png

Figure 1 - Underwater portion of the SWATH chassis design.

 

thrusterpanel.png

Figure 2 - Thruster panel 

Requirements

Ballast Tanks

The chassis is designed to hold 2 sets of ballast tanks, one set at the front of each hull and one set at the back of each hull. These ballast tanks are connected to 2 water pumps that can fill or empty the ballasts when needed. The ballast tanks must be full at all times to keep the SWATH stable. 

 ballast.png

Figure 2 - Ballast tanks and hull.

Foam Liner Compartment 

The foam liner compartment is a layer of foam under the belly of the SWATH concept car. The foam liner compartment ensures that the SWATH does not sink even if it is filled with water.

 

RudderletsRudders and Tail

RudderletsRudders are small boat-shaped rudders that can turn clockwise and counter clockwise.

rudderlet1.png

Figure 3 - Side view of a rudderletrudder

 

rudderlet2.png

Figure 4- Top view of a rudderletrudder

Placing theRudders Rudderlets and Tail

A set of 4 rudderletsrudders are placed at the bottomfront of each hullhull. awayA frompair of tails are placed at the ballastrear tanks.of each hull.

g11384.png

Figure 5 - Bottom view of the hull with rudderletsrudders and tail

 

g11464.png

Figure 6 - Side view of a hull with rudderletsrudders

Each rudderletrudder has a connector rod that is placed perpendicularly to the central axis of the rudderlet.rudder. The connector rod is then connected to a control rod that connects all the rudderletsrudders together.

conteolrod.png

Figure 7 - Top view of the connector and control rods

 

g10402.png

Figure 7 - Side view of the connector and control rods

 

g10778.png

Figure 8 - Front view of the rudderlet,rudder, connector and control rods

 

 

 

Tail

The tail is a boat shaped structure that is placed at the rear of the hull away from the ballast tank. The tail is fixed and cannot rotate. It keeps the craft stable and easy to maneuver. 

 

RudderletRudder Movement

Each rudderletrudder is fixed to the base of the hull and can rotate clockwise and counter clockwise along its axis. 

 

 

 

The other end of each connecting rod is connected to a control rod in each hull. The control rods are designed to move forward and backward to enable the rudderletsrudders to turn clockwise or counter clockwise. 

The 2 control rods from each hull are controlled by the central steering system.

Figure 

Figure

Figure

 

Thruster Panel

A thruster panel is designed to hold 4 rim-driven thrusters. Each thruster is controlled independently from the navigation console. It is placed between the 2 hulls and housed in the chassis. The depth of the thruster panel can be adjusted from the navigation console. 

 

Helm (Steering ControlControl) System

The steering control system consists of a steering wheel that centrally connects to the control rods inside each hull. Turning the steering wheel clockwise or counter clockwise turns the direction of the rudderlets.rudders.

 

 

 

  • Control between one to four thrusters (electric motor-driven propellers or RIM drive motors) of up to 2 kilowatts per thruster.  
  • Each thruster should be able to be controlled in forward and reverse movement.
  • Precise control of between one and five control surfaces like rudders and fins using marine grade stepper motors so we have directional control and they could potentially be used for stabilizing movement when stationary in the water.
  • A fuel level indicator for gas or diesel.
  • A battery charge level indicator.
  • Control four trim tanks: We will have multiple trim tanks which can be filled or emptied with water with pumps. Two tanks will be at the front (one on the left and one on the right hull). Two tanks will be at the back (one on the left and one on the right hul). These tanks do not need to fill or empty water too fast as the trim will not need to be changed often or rapidly on each trip. They will help keep the vessel level when weight is moved around on the passenger platform. We will need pumps to move the water or air from tank to tank.
  • Control four buoyancy tanks: We will have up to four buoyancy control tanks which will add/remove water/air as needed from the tanks to adjust the height of the vessel depending on whether the vessel is in movement or docked or in other situations that require the height to be adjusted.
  • All pumps will run on 12, 24, or 48VDC (TBD).
  • Movement sensor (9 axis accelerometer)
  • Water level sensor in buoyancy tanks
  • Water level sensor of the vessel relative to the ocean
  • Water/air temperature sensor - Optional
  • Additional sensors - Optional
  • The vessel should be able to connect via API to the Ocean Builders web server when in range of the internet (specific APIs to be determined later) - BONUS

 

  

 

Licensing

This project is being developed as an open-source project with the following licensing:

Back to top